
-
PRiCO
PRiCO (Programmble intelligent Counter)
PRiCO provides a very cost - effective and reliable solution to many complex counting requirement.
What sets PRiCO apart from the convention facet. -
SPECIFICATIONS :
Counting modes
- » Up counting
- » Down counting
- » Quadrature counting
- » Bi-directional counting
Display
7-digit, seven segment LED display (10mm height)
- » Counter/Totaliser/Batch: 7- digit display
- » Rate : 5- digit display
- » RPM : 6- digit display
Range
- » Counter/Totaliser:Selectable least count 0.000001, 0.00001, 0.0001, 0.001, 0.01, 0.1, 1
- » Rate: Rate per minute (RM) / Rate per hour (RH) user selectable. (minimum frequency for Rate mode is 10 Pulses/minute)
- » RPM: 10 RPM to 360000 RPM
Set points
- » 3 user programmable set points.
- » SET1 , SET2 :Dedicated for COUNTER mode.
- » SET3 : User programmable for any one of COUNTER / TOTALISER /BATCH / RPM.
Relay operating mode
- » Relay ON mode
- » Relay OFF mode
- » Pulse time mode
a) Time pulse repeat mode
b) Auto-reset mode
Count inputs
- » Voltage pulse : 8 to 30 V DC amplitude from proximity switch, encoder.
- » Potential free contacts from limit switch, micro switch.
Input frequency
- » 0 to 6 KHZ: In up / down mode
- » 0 to 3 KHZ: In quadrature mode / bi-directional mode.
Sensor supply
- » 12 V DC, 60mA (+/- 10 %)
Scale factor
- » Programmable
- » scale factor = X x 10Y
X = From 0.000001 to 9.999999
Y = 0, 1, 2, -1, -2, -3, -4, -5
Reset input
- » Manual / Front panel reset: with enable / disable facility
- » Remote/ Back panel / Electrical reset: User selectable
( minimum time for remote reset is 10 ms. ) - » Reset through programming mode: User selectable
Relay outputs
- » Three Relays ( one relay for each set point )
- » Relay1/ Relay2 for set1/set2 operation ( COUNTER )
- » Relay3 for set3 ( COUNTER / TOTALISER / BATCH / RPM ) – Programmable
- » Relay ratings: Rated for 5 Amp at 230 V AC
Memory retention
- » Upto 10 years
Protection
- » Parameters
a) Password protected
b) Hardware protected (Dip switch setting) - » Set points
a) Software protected (Through program configuration i.e. ‘SdF 3.’)
Supply
- » 230 V AC (+/- 10%)
Mounting
- » Panel mounting
Weight
- » approximately 580 gms
Operating temperature
- » 0° to 50° C
Relative humidity
- » 10 - 95% non-condensing
Overall dimensions
- » (All dimensions are in mm.)
Front View Side View Panel cutout -
OTHER COUNTERS :
-
Totaliser Cum Rate Indicator
TOTALISER CUM RATE INDICATOR SUPPLY 230V AC +/- 10% INPUT PROXIMITY SENSOR (PNP or NPN) DISPLAY 6 DIGIT LED FOR TOTAL
4 DIGIT LED FOR RPMRANGE 0-999999 FOR TOTAL
10-9999 FOR RPMSET POINT 1 OUTPUT RELAY C/O FOR TOTAL RELAY CONTACT RATING @5A LOAD FOR 230V AC SIZE 48 X 96 X 110MM (H X W X D) CUTOUT 45 X 90 MODEL IC202
-
SPEED CONTROLLER SUPPLY 230V AC +/- 10% INPUT PROXIMITY SENSOR (PNP or NPN) DISPLAY 4 DIGIT LED RANGE 10-9999 RPM (4 DIGIT) SET POINT 2 OUTPUT 2 INDEPENDENT RELAY C/O
FOR UNDER SPEED AND OVER
SPEED INITIAL BY PASS TIME
0-99.9 MINRELAY CONTACT RATING @5A LOAD FOR 230V AC SIZE 48 X 96 X 110MM (H X W X D) CUTOUT 45 X 90 MODEL IC303